SPECIFICAION of led power supply
MODEL SMT-012-060VW SMT-024-060VW SMT-036-060VW
OUTPUT DC VOLTAGE 12V 24V 36V
RATED CURRENT 5.0A 2.5A 1.66A
CURRENT RANGE 0~5.0A 0~2.5A 0~1.66A
RATED POWER 60W 60W 60W
RIPPLE&NOISE(max) 1.2V 1.2V 1.2V
voltage TOLERANCE 12V±5% 24V±5% 36V±5%
SETUP RISE TIME 80ms/110,220VAC 80ms/110,220VAC 80ms/110,220VAC
HOLD UP TIME(Typ.) 60ms/110,220VAC 60ms/110,220VAC 60ms/110,220VAC
INPUT VOLTAGE RANGE 90~135/170~265Vac 90~135/170~265Vac 90~135/170~265Vac
FREQUENCY RANGE 50~60Hz 50~60Hz 50~60Hz
POWER FACTOR(Typ.)
EFFICIENCY(Typ.) >84% >84% >84%
AC CURRENT(Typ.) 0.5A/110V,220VAC 0.5A/110V,220VAC 0.5A/110V,220VAC
INRUSH CURRENT (Typ.) COLD START 30A/110,220VAC
PROTECTION Short circuit Protection type:recovers automatically after condition is removed
Overload overload protected@145-160% above peak rating
Over temperature Protection type:Shut down o/p voltage,re-power on to removed
ENVIRONMENT WORKING TEMP. -30~+50℃ (Refer to output load derating curve)
WORKING HUMIDITY 20~99% RH non-condensing(Waterproof)
STORAGE TEMP.,HUMIDITY -40~+80℃,10~99%RH
SAFETY&EMC SAFETY STANDARDS
CE Mark(LVD),IP67
WITHSTAND VOLTAGE I/P-O/P:1.5KVAC IP-GND:1.5KVAC
EMC Test Standards EN55015:2006;EN61547:1995+2000;EN61000-3-2:2006
EN61000-3-3:1995+A2:2005;EN61346-1:2001;EN61347-2-13:2006
NOTE
1.All parameters NOT specially mentoned are measured at 110VAC, 220VAC input,
rated load and 25℃ of ambient temperature.
2.Ripple&noise are measured at 20MHz of bandwidth by using a 12" twisted
pair-wire terminated with a 0.1uf&10uf parallel capacitor.
3.Tolerance:includes set up tolerance,line regulation and load regulation.
Features of constant voltage power supply
High efficiency,save energy ,protected environment.
High stability and low ripple, increase light efficiency and decrease light attenuation.
Meet to safety standard and EMC
Assure LED stability long lift and light efficiency by constant voltage.
Integrity protection,over loading, over voltage ,over current.
8Hrs and 100% full load burn-in test.
Environment of power supply 24v 60w
Working Temperature : -25 ~ +50°C
Working Humidity : 20 ~ 90% RH non-condensing
Storage Temp. , Humidity : -40 ~ +80°C , 10 ~ 95% RH
TEMP. Coefficient : ±0.03%/°C (0 ~ 50°C)
Vibration : 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
Safety:
Safety Standards : IEC 61347 –2–11 , IEC 61347 –1 , IEC 60529 , IP67 approved
Withstand Voltage : I/P-O/P: 3000KVAC
Isolation Resistance : I/P-O/P:100M Ohms/500VDC
